Integrating modern technologies in water treatment process control

0
Water treatment industry: Process control is vital to ensuring the integrity of the water supply chain, in civil and industrial applications.

Water treatment industry: Process control is vital to ensuring the integrity of the water supply chain, in civil and industrial applications.

Process control is vital to ensuring the integrity of the water supply chain, in civil and industrial applications.

Water is a finite resource and so the efficient management of this resource is a key driving factor behind industry investment. Much of the water that we use every day is actually on a continuous loop, constantly being processed after use so that it can be returned to the environment before it is extracted again, treated and reused. This process is heavily dependent upon precise process control, monitoring and data recording to ensure that all the regulatory standards are maintained as well as ensuring that the environment and the general population is protected.

In general, the water treatment industry prefers to operate a centralised control system for each site, making it quicker and easier for operators to assess the equipment and processes on the site. With such a wide array of sensors, valves and pumps installed around the site, the most efficient controller will be one that is capable of multiple tasks while still being simple to operate.

One example would be Bürkert’s type 8619 MultiCELL transmitter/controller, which utilises pH, conductivity and flow sensors, ORP and temperature measurements. This product is ideal for a wide range of applications in water treatment. The major advantage of this controller is its versatility; being compatible with most common sensors as well as utilising a modular design which allows additional hardware and software to be added easily.

Each controller can be configured for a range of sensors as well as having up to six pre-configured I/O boards to accommodate any signal requirements. In addition, the MultiCELL can be configured as a datalogger, using the built-in SD card slot for data storage. This SD card slot can also be used to save sensor parameters and control application settings to allow the same settings to be replicated in other MultiCELL controllers; ensuring the accurate transfer of control parameters between sites.

The multifunction controller has been designed with both the installer and the operator in mind. The huge range of features and the modular design allows the system to be customised to the clients’ exact requirements, while the easy, intuitive user interface can be configured in four different views to display the most relevant information to a particular application. Different users can configure different views, depending on the area of control they are interested in.

Designing a system such as this essentially allows costs to be reduced in the processing applications; a systems engineer can, in many instances, replace an entire control cabinet with one neat controller that utilises a built-in display. The relative costs of a separate enclosure, rack mounted plc, I/O, cabling, power supply, HMI etc. can effectively be replaced with just one MultiCELL unit. Not great news for the panel building industry you would think, but cutting costs and streamlining installations is the name of the game and this type of knowledge can prove invaluable.

Furthermore, the advantage of this modular expansion facility is that MultiCELL users only pay for the features that they actually require. Since the MultiCELL provides a single controller/transmitter across a wide range of applications, inventory and training costs are also minimised. In the long term, the total cost of ownership is greatly reduced when compared to the systems currently in use. This unit is designed specifically to be panel mounted, either internally or on a door or bulkhead. Using this technology, a panel can be downsized, through the use but technologically up-sold.

Similar principles have also been used in the design of the mxCONTROL multifunction controller, type 8620, which has the additional benefits of Ethernet or modem communication as well as the ability to control digital dosing pumps. The flexible programming capabilities enable integrators and end users to make fast program modifications during commissioning and maintenance.

Again, there is an SD card slot for data logging and saving parameter settings to save time when installing many units across different sites. By using a simple user interface, easily configured control programs and common sensors the whole process from design to implementation is streamlined for efficiency, reducing training time, parts inventory and overall cost of ownership.

Both solutions allow direct connection to existing SCADA systems and other methods of site-wide monitoring and supervisory control, so adding connectivity to PH sensors and flow meters for example can add to the automation efficiency of a plant, while supporting the case put forward by the panel builder or integrator for a smarter solution.

Share.